C175-16 Generator Set

C175-16 Generator Set

Caterpillar is leading the power generation marketplace with Power Solutions engineered to deliver unmatched flexibility, expandability, reliability, and cost-effectiveness.

Generator Set Specifications
Standby Rating
3365(no fan)/3250/3100(no fan)/3000 ekW
Prime Power Rating
3115(no fan)/3000/2825(no fan)/2725 ekW
Emissions/Fuel Strategy
Low Fuel, Tier 2
Voltage
480 to 13800 Volts
Frequency
60 Hz
Speed
1800 RPM
Duty Cycle
Standby, Mission Critical, Prime, Continuous
Maximum Rating
3365 ekW
Minimum Rating
2500 ekW
Engine Specifications
Engine Model
C175-16 SCAC, V-16, 4-Stroke Water-Cooled Diesel
Bore
6.89in
Stroke
8.66in
Displacement
6456.31in³
Compression Ratio
16.7:1
Aspiration
Turbo Aftercooled
Fuel System
Common Rail
Governor Type
ADEM� A4
Generator Set Dimensions
Length - Minimum
241.6in
Length - Maximum
312.9in
Width - Minimum
83.1in
Width - Maximum
113.7in
Height - Minimum
87in
Height - Maximum
134.3in
Dry Weight - Genset (minimum)
42750lb
Dry Weight - Genset (maximum)
50500lb

Standard Equipment:

Air Inlet System
  • 4 x Single element canister with service indicator(s).
 
Control Panel
  • 2 Programmable relay outputs (Form C)
  • Low coolant level
  • Over / under voltage
  • Coolant temperature
  • Serial annunciator module data link
  • Alarm acknowledge
  • Text alarm/event descriptions
  • Volts (L-L & L-N)
  • Reverse power
  • Over / under frequency
  • Environmental sealed front face
  • Programmable Protective Relaying Functions
  • Speed adjust
  • Generator phase sequence
  • Low coolant temperature
  • Generator mounted - rear facing
  • Overspeed
  • Controls
  • Frequency (Hz)
  • Engine cycle crank
  • Engine cool-down timer
  • Warning / Shutdown Indicators
  • Lamp test
  • 2 Programmable digital outputs
  • 6 Programmable digital inputs
  • High coolant temperature
  • Customer data link (Modbus RTU)
  • Auto / start / stop control
  • Emergency stop pushbutton
  • RPM
  • Digital Indicators
  • Communications
  • Accessory module data link
  • Oil pressure (psi, kPa or bar)
  • Low oil pressure
  • Overcurrent
  • Emergency stop
  • 24 Volt DC operation
  • 4 Programmable relay outputs (Form A)
  • Failure to start (overcrank)
  • True RMS AC metering, 3-phase, +/-2% accuracy
  • Power Factor (per phase & average)
  • Operating hours
  • DC volts
  • Amps (per phase & average)
  • EMCP 4.2B
  • Reverse reactive power
 
Exhaust System
  • Bolted flange, with bellow for each turbo
  • Exhaust flange outlet
 
Fuel System
  • Engine mounted filters #REF!
  • Filters x 3
  • 10 Micron spin on yype
  • Secondary / tertiary fuel filters
  • 4 Micron spin on type
  • Primary fuel filter water / fuel water separator
 
Generators And Attachments
  • Right side extension box, bottom cable entry
  • IEC Platinum stator RTDs
  • Reactive droop capability
  • 3 Phase voltage sensing
  • (MV) Busbar connections, right side extension box, bottom cable entry
  • Class F temperature rise at 40C ambient
  • Anti condensation space heater
  • NEMA Class H insulation
  • 6 Leads
  • Class H temperature rise at 40C ambient
  • Voltage regulator:
  • Exciter diode monitor
  • Form wound
  • RFI suppression
  • (LV) Busbar connections, top/center mounted, top cable entry
  • 3 Phase brushless
  • 60 Hz models: NEMA standard hole pattern
  • Permanent magnet
  • Min / max exciter limiter
  • Salient Pole
 
Governing System
  • Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
  • ADEM A4
 
Lube System
  • Oil filter, filler and dipstick
  • Integral lube oil cooler
  • Oil drain lines and valve
  • Fumes disposal
  • Lubricating oil
  • Prelube - required with prime, continuous, and standby
  • Gear type lube oil pump
 
Mounting Systems
  • Rails - Engine / generator
  • Rubber anti-vibration mounts (shipped loose)
  • Dual 24 volt electric starting motors
  • Battery disconnect switch
  • Batteries and battery rack w/cables
 
Power Termination
  • Busbar
 
Service Instructions
  • Two PM inspections
 
General
  • Paint - Caterpillar yellow with high gloss black rails & radiator
  • SAE standard rotation
  • LH Service
  • Flywheel and flywheel housing-SAE No. 00
 

Optional Equipment:

Air Inlet System
  • Air inlet adapters
  • Dual element air cleaner
  • Single element air cleaner
  • Air inlet protection
 
Control Panel
  • Package mounted radiator
  • Automatically selected ground
  • Customer AC-DC connection mounting location - LV/MV
  • Load share governor
  • EMCP 4.3, EMCP 4.4
  • E-Stop
  • Frame boxes
  • Annunciator modules
  • Load share module / auxiliary plate and auxiliary box (LV)
  • Fuel cooler
  • EMCP mounting location - LV/MV
  • Modbus monitoring of packages
  • Customer interface options
  • EMCP 4.4 optional harness
  • EMCP voltage and current sensing groups
  • Remote radiators
  • Generator harness
  • Interconnect harness
  • Speed adjust
  • EMCP and MV and HV power connection locations
  • Raise lower switch
 
Crankcase Systems
  • Explosive relief valves
  • Crankcase ventilation system
 
Exhaust System
  • Mufflers
  • Exhaust support group
  • Weld flanges
  • Exhaust collectors / Manifold
  • Front housing - Prime or continuous
  • Front housing - Standby or mission critical
  • Aftercooler drain
 
Fuel System
  • Primary fuel filter
 
Generators And Attachments
  • Low voltage - 1800 and 3000 Frames - 60 Hz, 3 phase, 1800 rpm, FW, PM, No of leads=6, Pitch 0.6667
  • Medium voltage - 1800 and 3000 Frames - 60 Hz, 3 phase, 1800 rpm, FW, PM, No of leads=6, Pitch 0.6667
  • Conversion GP-Top cable entry
  • Low voltage - 1800 and 3000 Frames - 50 Hz, 3 phase, 1500 rpm, FW, PM, No of leads=6, Pitch 0.6667
  • Differential current transformers
  • Space heater kit
  • Medium voltage - 1800 and 3000 Frames - 50 Hz, 3 phase, 1500 rpm, FW, PM, No of leads=6, Pitch 0.6667
  • Thermostat for space heater
  • Generator air intake
 
Instrumentation
  • Pyrometer and thermocouples
 
Lube System
  • Drain group oil pans
  • Oil filters
  • Lube oil heater
  • Electric prelube pumps
  • Lubricating oil
 
Mounting Systems
  • IBC vibration isolators - Shipped loose
  • Spring type linear vibration isolators
  • Rubber anti-vibration mounts
 
Power Connections
  • Low voltage connection cable
  • Center post busbars (LV)
  • 1800 Frame generator side / rear mounted busbars (MV)
  • Enclosures - Control packaging (LV)
  • Paralleling circuit breakers
  • 1800 Frame generators circuit breaker
  • Neutral ground (LV)
  • Neutral ground (MV)
  • Cable entry options (LV)
  • Cable entry options (MV)
  • Masterpack breakers
  • Power connection covers (LV)
  • Harnesses (Breaker)
  • Masterpack breaker connections
  • Side / Rear mounted busbars (LV)
 
Special Tests / Reports
  • IBC seismic certification
  • Special test charge - Engine only
  • PGS test report @ 0.8 power factor
  • Genset fuel consumption test
  • Standard genset TVA (Torsional vibration analysis) report
  • PGS test report @ 1.0 power factor
  • OSCOSH1 seismic certification
  • Custom genset TVA report
  • Generator test report
  • Standard engine test charge
 
Starting / Charging System
  • Heavy duty battery sets with rack
  • Charging alternators - Dry
  • Air pressure regulator
  • Starter location covers
  • 24 Volt power distribution box
  • 24 Volt electric starting motors
  • 35 Amp battery chargers
  • 24 Volt battery sets - Dry
  • 20 Amp battery chargers
  • Jacket water heaters
  • 50 Amp battery chargers
  • Air starting motor
  • Jacket water heater wiring groups
 
General
  • Special paint colors
  • Control GP - Air powered bar group
  • Barring group manual
  • Service tools - Engine barring group
  • Engine barring air powered
 

    This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

    Share This Product