C9 ACERT™ Hazardous Location Engine

C9 ACERT™ Hazardous Location Engine

C9 ACERT™ Hazardous Location Engine

Cat C9 ACERT hazardous location engines are the ideal solution for specialized and demanding operations in the oilfield. Engines are hazardous-location certified from the factory to minimize installation design, time, and cost. Decades of field operation and intense research and development allow Cat C9 ACERT hazardous location engines to deliver excellent performance with low operating costs and emissions.Hazardous location engines are certified to operate in potentially explosive environments. Applications powered by C9 ACERT engines include workover rigs, pump skids, acidizing units, cementing units, coil tubing units, and hydraulic power units. Cat engines are backed by the worldwide network of Cat dealers ready to support your operation with technical support, service, parts, and warranty.C9 ACERT hazardous location engines, with ratings 254 bkW (340 bhp) @ 2200 rpm meet IMO Tier II, EPA Non-road Tier 3 equivalent and EU Stage IIIA equivalent emission standards. They are available using U.S. EPA and EU Flexibility, and for other regulated and non-regulated areas.

General Specifications
Maximum Rating
340BHP
Displacement
537.96in³
Minimum Rating
340BHP
Governor and Protection
Electronic (ADEM™ A4)
RPM
2200r/min
Aspiration
Turbocharged-Aftercooled
Flywheel and Flywheel Housing
SAE 1 or 2
Flywheel Teeth
113 (SAE 1), 134 (SAE 2)
Rotation from Flywheel End
Counterclockwise
Stroke
5.9in
Bore
4.4in
Emissions
Emissions
EPA and CARB Non-Road Tier 3, EU Stage IIIA, EPA Marine Tier 2, IMO Tier II
Dimensions
Length
44.4in
Width
35.1in
Height
42.6in
Weight
2219lb
Capacity for Liquids
Lube Oil System - Refill
8gal (US)
Cooling System
3.7gal (US)

Standard Equipment:

Air Inlet System
  • Turbocharger, separate circuit (SCAC) or remote (REMAC) aftercooler
  • Single, right-side, center-mounted turbo with water-cooled turbine housing
  • Air inlet 101.6 mm (4 in) connection type
 
Control System
  • Electronic governing, PTO speed control
  • Programmable ratings
  • Cold mode start strategy
  • Automatic altitude compensation
  • Fuel cooled ECU
  • Power compensation for fuel temperature
  • Programmable low and high idle
  • Electronic diagnostics and fault logging
  • Programmable monitoring system (engine speed, temperature, pressure)
  • J1939 broadcast (diagnostic and engine status)
  • Certified electrical control system (hazardous environment only)
  • Derated engine: automatic ambient temperature compensation
 
Cooling System
  • Thermostats and housing, RH forward-facing outlet — 51 mm (2.01 in) connection
  • Jacket water pump — belt-driven, centrifugal
  • Water pump — inlet RH facing downward 63 mm (2.48 in)
 
Exhaust System
  • Exhaust manifold — wet
  • Single, right-side, center-mounted turbo with water-cooled turbine housing
  • Rear facing turbo exhaust 81.8 mm (3.22 in.) connection, non V-band clamp
 
Flywheels And Flywheel Housing
  • Mandatory selection of:SAE No. 1 or SAE No. 2 flywheel and housing, SAE standard rotation
 
Fuel System
  • HEUI fuel system
  • Fuel filter — secondary, LH (2-micron high performance)
  • Fuel transfer pump — left front
  • Fuel priming pump — left front
 
Lube System
  • Crankcase breather — LH
  • Crankcase fumes disposal — with integrated service indicator, LH
  • Oil cooler — RH
  • Oil filter — RH
  • Oil pan — front sump
  • Oil filler — top mounted
  • Oil level gauge — LH side
  • Oil pump — gear-driven
  • Oil valve sampling
  • Preservation of turbocharger, flywheel, and crankcase
 
Power Take-offs
  • Crankshaft drive pulley — 2 grooves, 190 mm (7.5 in) diameter, 22.3 mm (7/8 in) wide
 
General
  • Vibration damper
  • Lifting eyes
  • Automatic variable timing — electronic
  • Literature
 
Mandatory Options
  • Flywheel housing and flywheel
  • Primary filter/water separator
  • Turbo orientation
 

Optional Equipment:

Air Inlet System
  • Air inlet elbow
  • Air shutoffs
 
Cooling System
  • Water outlet elbow
  • Coolant conditioner
 
Flywheels And Flywheel Housing
  • Crankshaft seal
 
Instrumentation
  • Gauges and instrument panels
  • Interconnect harness
 
Lube System
  • Oil pans
  • Drain and cover
  • Remote oil filters
  • Lubricating oils
 
Mounting System
  • Structural steel base
  • Engine support — front and rear
 
Power Take-offs
  • Rear enclosed clutches
  • Hydraulic pump drives
  • Hydraulic gear pumps
  • Clutch supports
  • Crankshaft pulleys
  • Transmission Arrangement
  • General
 

    This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

    Share This Product